[vc_row row_type=”row” use_row_as_full_screen_section=”no” type=”full_width” text_align=”center” box_shadow_on_row=”no”][vc_column width=”1/6″][vc_single_image image=”349144″ style=”vc_box_border”][vc_column_text]

AT-CPCI-SBC

[/vc_column_text][/vc_column][vc_column width=”5/6″][vc_column_text][/vc_column_text][vc_column_text]

The AT-cPCI-SBC-CELERONM is an exceptionally high integration, high performance, rugged and high quality Card that contains all the component subsystems of an ATX motherboard with cPCI Back Plane Interface. This enables it to be used in systems designed around cPCI Architecture. The cPCI card has a Computer on Module ETX802 plugged into it. ETX802 is based on one of the ultra high performance, high-integration Intel Celeron M processors and gives designers the choice of a complete, high performance, rugged, embedded processor based on the ETX form factor that conforms to the ETX V2.7 specification. The module plugs into the card, which has connectors and additional circuitry to meet your application requirements.

[/vc_column_text][vc_separator type=”transparent” up=”38″ up_style=”px” down=”0″ down_style=”px”][/vc_column][/vc_row][vc_row row_type=”row” use_row_as_full_screen_section=”no” type=”full_width” text_align=”center” box_shadow_on_row=”no”][vc_column][no_tabs style=”horizontal_left” tab_border_radius=”0″][no_tab icon_pack=”font_awesome” title=”Features” tab_id=”1331232476″][vc_separator type=”transparent” up=”15″ up_style=”px” down=”0″ down_style=”px”][vc_column_text]

  • 6U HT Single Slot width 6U Compact PCI Form Factor Card
  • Compliance to PICMG 2.0 R3.0 compactPCI Specification
  1. On Card ETX Computer On Module specification:
  2. 1.0GHz Ultra Low Voltage Intel Celeron M (Dothan)
  3. Cache – 1MB L2 Cache, FSB – 400 Mhz
  4. Chipset – Intel 855GME/ECH4M
  5. System Controller – PC Compatible DMA and Interrupt controller, timers & Watchdog Timer
  6. DDR SDRAM up to 1GB capacity using SO-DIMM Main Flash – IDE
  7. Compact Flash up to 8 GB
  8. Three USB 2.0 Ports available on back panel Connectors
  9. Six RS422 Channels
  10. One AC’97 Audio Port, One VGA port
  11. PS2 Keyboard and Mouse Interface
  12. ISA and PCI (32 bit/33Mhz) Bus interfaces

 

  • Additional features on the card:
  1. Two Dual redundant 1553B Channels programmable as BC/RT/MT
  2. One 10/100BaseT Gigabit Ethernet Port
  3. One USB2.0 port for Auxiliary Flash Disk Interface
  4. One Virtex 4 LX60 FPGA to Handle IO requirements as per ICD
  5. 5V TTL/CMOS Differential Inputs – 16 Nos
  6. 5V TTL/CMOS Differential Outputs – 40 Nos
  7. 8 x 28V/Open Inputs
  8. 8 x 28V/Open or GND/Open Outputs
  9. One 3.125Gbps LVDS channel
  10. Rear IO Connectivity to all the interfaces through Rear IO transition Board
  11. Rugged Version with Heat Sink Metal Plate and Card Wedge Locks
  12. +5V and +3.3V Back Plane supplied Power

[/vc_column_text][vc_separator type=”transparent” up=”7″ up_style=”px” down=”0″ down_style=”px”][/no_tab][no_tab icon_pack=”font_awesome” title=”Product Specification” tab_id=”1279324092″][vc_separator type=”transparent” up=”15″ up_style=”px” down=”0″ down_style=”px”][vc_column_text]CPU
1.0 GHz Ultra Low Voltage (ULV) Celeron® M 373 (with 512 KB L2 cache) processor
Front Side Bus (FSB) of 400 MHz

 

Memory
Single 200-pin DDR SODIMM socket provided
Supports a single +2.5V DDR RAM SODIMM up to 1 GB
Supports PC2700 DDR 333 (166 MHz)

 

PCI Bus/ISA Bus
PCI 2.2 compliant (32 bit/33Mhz)
DISA bus speed at 8 Mhz

 

IDE Interfaces
Supports two enhanced IDE controllers (4 devices)
Supports dual bus master mode
Supports Ultra DMA 33/66/100 modes
Supports ATAPI and DVD peripherals
Supports IDE native and ATA compatibility modes

 

Serial Ports
Two buffered TTL serial ports with full handshaking (transceivers on baseboard) provided
Provides two 16550-equivalent controllers, each with a built-in 16-byte FIFO buffer
Provides programmable word length, stop bits and parity
Provides 16-bit programmable baud-rate generator
Provides full modem capability
RS422 Ports
Provides for Six RS422 ports connected to user IO connector
Accessible through Rear IO Transition Board

 

USB Ports
Supports two root USB hubs
Supports four USB ports
Supports USB v2.0 and legacy v1.1
Supports over-current fuses on baseboard
Supports USB Boot and the respective USB Boot devices
Three USB 2.0 ports made available at the connectors
One USB 2.0 port for access to compact flash in offline mode

 

Keyboard/Mouse Interface
Supports PS/2 keyboard & mouse

 

Audio Interface
Supports AC’97 standard
AC’97 CODEC provided on-board
Audio amplifier provided on the card

 

Ethernet Interface
Intel 82551QM Controller and one Ethernet port provided
Supports magnetic and RJ45 connector on baseboard
Supports IEEE 802.3 10BaseT/100BaseTX compatible physical layer
Supports Auto-negotiation for speed and duplex mode
Supports full duplex or half-duplex mode
Full-duplex mode uses IEEE 802.3x flow control to transmit and receive frames simultaneously
Half-duplex mode supports enhance proprietary collision reduction mode
Intel 82540EP based 10/100/1000 Base TX port
Both the ports routed to Back Plane User IO Connectors and accessible using Rear IO Transition Board

 

Video Interfaces (Crt)
Supports CRT (1600 x 1200) with 64 MB UMA (Unified Memory Architecture)
Integrated 128-bit graphics controller provided

 

JTAG
On-board JTAG chain for FPGA’s
On-board JTAG header for CPLD programming
On-board JTAG interface to the processor for debugging and development purposes

 

Miscellaneous
Real-Time Clock (RTC) with external battery provided
Supports battery-free boot
Watchdog Timer feature provided

 

I/O Interfaces
40 x TTL Differential o/p channels
16 x TTL Differential i/p Channels
8 x 28V/ Open Inputs
8 x 28V / Open or GND/Open Outputs

 

LVDS Channel
One LVDS TX Channel of data rates of up to 1.125 Gbps
One LVDS RX Channel of data rates of up to 1.125 Gbps
With combined data rates of up to 3.25Gbps in full Duplex mode
Provided using external LVDS transceiver interfaced to FPGA

 

FPGA
Provides on On-board Virtex 4 LX60 FPGA
FPGA customizable to handle various digital IOs as per customer LCD
Interfaced to Processor on North Bridge on PCI Bus

 

Mechanical
6U compactPCI card
Board Dimensions: 160mm x 233mm
Board thickness: 2.4mm
Rugged Version with Heat Sink Metal Plate and Card Wedge Locks

 

Power
Derived from +5.0V and +3.3V of Back Plane
All other voltages internally derived
Power Consumption 20-Watts Approx

 

Environmental
Air-Cooled     Conduction-Cooled
Operating temperature     0ºC to +60ºC     -40ºC to +85ºC

 

Operating Systems Support
VxWorks (Ver 6.3 workbench 2.5) Board Support Package (BSP), Windows CE (Ver 6.0) and Windows XP

 

Warranty
1 year limited warranty[/vc_column_text][vc_separator type=”transparent” up=”7″ up_style=”px” down=”0″ down_style=”px”][/no_tab][no_tab icon_pack=”font_awesome” title=”Ordering Information” tab_id=”940990757″][vc_single_image image=”349174″ img_size=”large”][vc_separator type=”transparent” up=”15″ up_style=”px” down=”0″ down_style=”px”][vc_separator type=”transparent” up=”7″ up_style=”px” down=”0″ down_style=”px”][/no_tab][no_tab icon_pack=”font_awesome” title=”Download Datasheets” tab_id=”9214113″][vc_separator type=”transparent” up=”15″ up_style=”px” down=”0″ down_style=”px”][vc_separator type=”transparent” up=”7″ up_style=”px” down=”0″ down_style=”px”][/no_tab][/no_tabs][/vc_column][/vc_row][vc_row row_type=”row” use_row_as_full_screen_section=”yes” type=”full_width” in_content_menu=”in_content_menu” text_align=”center” box_shadow_on_row=”no”][vc_column width=”1/2″ offset=”vc_col-lg-6 vc_col-md-6″][vc_separator type=”transparent” up=”38″ up_style=”px” down=”0″ down_style=”px”][/vc_column][/vc_row][vc_row row_type=”row” use_row_as_full_screen_section=”no” type=”full_width” text_align=”left” box_shadow_on_row=”no”][vc_column][vc_column_text]

[/vc_column_text][/vc_column][/vc_row]