AdTEC | AT-cPCI-SBC
350994
single,single-product,postid-350994,eltd-cpt-1.0,woocommerce,woocommerce-page,columns-3,,ajax_fade,page_not_loaded,moose-ver-1.1.1, vertical_menu_background_opacity, vertical_menu_with_scroll,smooth_scroll,woocommerce_installed,blog_installed,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
, , , ,

AT-cPCI-SBC

6U HT Single Slot width 6U Compact PCI Form Factor Card
Compliance to PICMG 2.0 R3.0 compactPCI Specification
 
On Card ETX Computer On Module specification:

  • 1.0GHz Ultra Low Voltage Intel Celeron M (Dothan)
  • Cache – 1MB L2 Cache, FSB – 400 Mhz
  • Chipset – Intel 855GME/ECH4M
  • System Controller – PC Compatible DMA and Interrupt controller, timers & Watchdog Timer
  • DDR SDRAM up to 1GB capacity using SO-DIMM Main Flash – IDE
  • Compact Flash up to 8 GB
  • Three USB 2.0 Ports available on back panel Connectors
  • Six RS422 Channels
  • One AC’97 Audio Port, One VGA port
  • PS2 Keyboard and Mouse Interface
  • ISA and PCI (32 bit/33Mhz) Bus interfaces

 
Additional features on the card:

  • Two Dual redundant 1553B Channels programmable as BC/RT/MT
  • One 10/100BaseT Gigabit Ethernet Port
  • One USB2.0 port for Auxiliary Flash Disk Interface
  • One Virtex 4 LX60 FPGA to Handle IO requirements as per ICD
  • 5V TTL/CMOS Differential Inputs – 16 Nos
  • 5V TTL/CMOS Differential Outputs – 40 Nos
  • 8 x 28V/Open Inputs
  • 8 x 28V/Open or GND/Open Outputs
  • One 3.125Gbps LVDS channel
  • Rear IO Connectivity to all the interfaces through Rear IO transition Board
  • Rugged Version with Heat Sink Metal Plate and Card Wedge Locks
  • +5V and +3.3V Back Plane supplied Power

The AT-cPCI-SBC-CELERONM is an exceptionally high integration, high performance, rugged and high quality Card that contains all the component subsystems of an ATX motherboard with cPCI Back Plane Interface. This enables it to be used in systems designed around cPCI Architecture. The cPCI card has a Computer on Module ETX802 plugged into it. ETX802 is based on one of the ultra high performance, high-integration Intel Celeron M processors and gives designers the choice of a complete, high performance, rugged, embedded processor based on the ETX form factor that conforms to the ETX V2.7 specification. The module plugs into the card, which has connectors and additional circuitry to meet your application requirements.

CPU
1.0 GHz Ultra Low Voltage (ULV) Celeron® M 373 (with 512 KB L2 cache) processor
Front Side Bus (FSB) of 400 MHz
 
Memory
Single 200-pin DDR SODIMM socket provided
Supports a single +2.5V DDR RAM SODIMM up to 1 GB
Supports PC2700 DDR 333 (166 MHz)
 
PCI Bus/ISA Bus
PCI 2.2 compliant (32 bit/33Mhz)
DISA bus speed at 8 Mhz
 
IDE Interfaces
Supports two enhanced IDE controllers (4 devices)
Supports dual bus master mode
Supports Ultra DMA 33/66/100 modes
Supports ATAPI and DVD peripherals
Supports IDE native and ATA compatibility modes
 
Serial Ports
Two buffered TTL serial ports with full handshaking (transceivers on baseboard) provided
Provides two 16550-equivalent controllers, each with a built-in 16-byte FIFO buffer
Provides programmable word length, stop bits and parity
Provides 16-bit programmable baud-rate generator
Provides full modem capability
 
RS422 Ports
Provides for Six RS422 ports connected to user IO connector
Accessible through Rear IO Transition Board
 
USB Ports
Supports two root USB hubs
Supports four USB ports
Supports USB v2.0 and legacy v1.1
Supports over-current fuses on baseboard
Supports USB Boot and the respective USB Boot devices
Three USB 2.0 ports made available at the connectors
One USB 2.0 port for access to compact flash in offline mode
 
Keyboard/Mouse Interface
Supports PS/2 keyboard & mouse
 
Audio Interface
Supports AC’97 standard
AC’97 CODEC provided on-board
Audio amplifier provided on the card
 
Ethernet Interface
Intel 82551QM Controller and one Ethernet port provided
Supports magnetic and RJ45 connector on baseboard
Supports IEEE 802.3 10BaseT/100BaseTX compatible physical layer
Supports Auto-negotiation for speed and duplex mode
Supports full duplex or half-duplex mode
Full-duplex mode uses IEEE 802.3x flow control to transmit and receive frames simultaneously
Half-duplex mode supports enhance proprietary collision reduction mode
Intel 82540EP based 10/100/1000 Base TX port
Both the ports routed to Back Plane User IO Connectors and accessible using Rear IO Transition Board
 
Video Interfaces (Crt)
Supports CRT (1600 x 1200) with 64 MB UMA (Unified Memory Architecture)
Integrated 128-bit graphics controller provided
 
JTAG
On-board JTAG chain for FPGA’s
On-board JTAG header for CPLD programming
On-board JTAG interface to the processor for debugging and development purposes
 
Miscellaneous
Real-Time Clock (RTC) with external battery provided
Supports battery-free boot
Watchdog Timer feature provided
 
I/O Interfaces
40 x TTL Differential o/p channels
16 x TTL Differential i/p Channels
8 x 28V/ Open Inputs
8 x 28V / Open or GND/Open Outputs
 
LVDS Channel
One LVDS TX Channel of data rates of up to 1.125 Gbps
One LVDS RX Channel of data rates of up to 1.125 Gbps
With combined data rates of up to 3.25Gbps in full Duplex mode
Provided using external LVDS transceiver interfaced to FPGA
 
FPGA
Provides on On-board Virtex 4 LX60 FPGA
FPGA customizable to handle various digital IOs as per customer LCD
Interfaced to Processor on North Bridge on PCI Bus
 
Mechanical
6U compactPCI card
Board Dimensions: 160mm x 233mm
Board thickness: 2.4mm
Rugged Version with Heat Sink Metal Plate and Card Wedge Locks
 
Power
Derived from +5.0V and +3.3V of Back Plane
All other voltages internally derived
Power Consumption 20-Watts Approx
 
Environmental

Air-Cooled Conduction-Cooled
Operating 0ºC to + 60ºC -40ºC to + 85ºC

 
Operating Systems Support
VxWorks (Ver 6.3 workbench 2.5) Board Support Package (BSP), Windows CE (Ver 6.0) and Windows XP
 
Warranty
1 year limited warranty

AT-CPCI-SBC-Celeronm-O